Shanghai Huai Tong Machinery Technology Co., Ltd. ---- Huairou world co Address: Daling Road, Pudong, Shanghai, China Zip Code: 200120 Contact Person: Mr. Wang Tel 021 -60498586 021-58433067 Sales Hotline: 15721364680 15821244425 Fax 021 -58,433,067 Contact QQ: 2563492433 gate opening device, also known as the gate opening Monitor is absolute rotary encoders, automatic closing devices or cables or other forms of couplers, display, controller, transmission cables, RS485 Digital communication interface and other components, gate motion sensor rotate through the coupler drive, you can output the corresponding gate Gray code phase encoded signals. Applicable to rivers, lakes, reservoirs, locks, hydropower and water supply and drainage engineering gate opening observation measurements. Contents 1 Introduction 2 Technical Specifications 3 Parameter 4 stroke 1 Introduction gate opening sensor, optional optical or mechanical series encoders, outside with mounting brackets, couplings or other gear coupling member composition. The sensor is coupled through a coupling member such as the encoder shaft and the spool shaft hoist or pinion shaft coupling, the encoder synchronous rotation with the shaft to be measured, the measured rotation of the shaft into rotation of the encoder shaft, collected through a dedicated tester encoder value to accurately measure the amount of displacement of the DUT. And reached the displacement of the DUT in real time measurement and control purposes. Suitable for all kinds of winch, hoist screw gate (flat doors, curved doors, miter gate, door, bridges, etc.) lifting height measurement. Gate opening device wiring Custom Picture 2 Technical Specifications Detection Range: 5m, 10m, 20m, 40,80 m Resolution: 1cm or 1mm Operating voltage: match the selected encoder measurement error: 0. 1% × span ± 1 Output Signal (determined by the selected encoder): Parallel Gray code signal (B), 4-20mA standard analog signal (A), RS485 serial signal (M), SSI synchronous serial Gray code signal (S) connection mode: Gear connection, flexible coupling connection, eccentric shaft coupling method, measuring rope hanging round hammer mode, chain sprockets connections and other environmental parameters: temperature -20 ℃ ~ +80 ℃, relative humidity ≤ 95% (RH40 ℃) () 3 Model BTM1213/RCH Mounting hole mounting Dimensions (WHD) 160 × 80 × 120 meter hole size 152 × 74 6 digit digital display input signal SSI synchronous serial signal 10-26 bits; an external set signal switch number 4 relay outputs, each position of a normally open a normally closed; panel default sensitivity settings, set the switch position signal output form all the way to the position signal output, one 4-20mA analog, all the way RS485 communication digital signal adjustment can be set to 4,20 mA corresponding value, 4,20 mA output trim zero, adjust the instrument comes with full protocol agreement, users can also be customized to provide protocol; panel settings can address any location set rate 0:00 set, the smart set or an external switch panel set operating voltage 220Vac (24Vdc can be customized) external power supply provides operating power sensor (specify when ordering voltage and current consumption) Operating Temperature -10 ℃ ~ 60 ℃ Relative humidity < 85% scaling factor linear displacement sensor code value for the scale factor set direction forward and reverse rotary encoder settings; linear displacement sensor settings can be pros and cons to set the 16-segment nonlinear nonlinear set or field correction, can be used to winch laminated, radial gates and other settings can be remote display two signals all the way into the PLC, all the way into the remote display instrument. Order Notice 1, gate opening sensor range 2, sensor resolution 3, the rope direction sensor 4, the output signal mode 5, the rope pulled out the gate movement direction 6, the signal input shaft revolution gate opening height of 7 bits, the , the lower limit value and the Number of Poles 4 stroke detection range: 5m, 10m, 20m, 40m, 80m Resolution: 1cm or 1mm Operating voltage: match the selected encoder measurement error: 0. 1% × span ± 1 appearance Size: 244mm * 116mm * height 208mm width output signal (determined by the selected encoder): Parallel Gray code signal (B) 4-20mA standard analog signal (A) RS485 serial signal (M) SSI Synchronous Serial Gray code signal (S) connection mode: wire rope directly linked with the measured outlet gate orientation: vertical down outlet, horizontal outlet, outlet upward outlet according to the user needs to determine the direction of the scene, the lower limit built: internal settings of the sensor on the main order, Lower bit cleared a key output of the encoder 485, SSI, or 4 ~ 20mA signal, press and hold the button for 3 seconds clears the encoder current value is "0" Environmental Parameters: Temperature -20 ℃ ~ +80 ℃, Relative humidity ≤ 95% (RH40 ℃)